Motorcycle Hot Grips Introduction
Operation principle is to transform the electric energy of the motorcycle magneto into heat energy, infrared electric heat material twine in to able to bear high temperature flexible shape skeleton wired trough of carving far at first, then penetrate the handle thread the lead wire column hole of skeleton, rivets and shuts with the heating wire tightly, and through welding it, in order to reduced and exposed to the resistance. Fix the heating wire and handle thread firmly with the glue at the same time,
in order to prevent the handle thread from being pulled out by the external force, one layer is able to bear high temperature and esthetic other glue set to put fixed handle thread and skeleton of the heating wire into molding plastics machine finally and mould plastics, enabling it becomes the whole, make the line of handle connect and fix the inside in the handle firmly.Because of adopting the patented technology ZI200320114747.7, make handle line, heating wire, skeleton and other glue set hot to combine into a whole, space of the middle pack, make it to be firm totally, prevent harmful gas and moisture from enter inside of handle lead to the fact the damage effectively, because there is no space of air at the same time, thermal resistance is reduced further, it is higher to spread thermal efficiency. Because of adopting molding plastics and encapsulating the craft disposable wholly,
the products are firmer and durable and lengthening its life-span. Through a few years’ lasting improvement, properties of product and quality have been already quite steady. In addition still adopt the following patented technologies and promote the competitiveness of the products by a large margin:
First, in order to improve and spread thermal efficiency and save the electric energy, the heating wire adopts and winds the craft of making intensively, make , generate heat surface increase , reduce other glue sets of thickness at the same time , make heat energy spread to the surface of handle rapidly, use patented technology increase , insulate against heat layer in charge of , in handle with metal direction in addition, prevent heat energy from being absorbed in a large amount by metal pipes, thus it is lower to enable and generate heat faster , power consumptive, temperature is higher.
Second, in order to prevent the other glue set from resulting in wearing out or breaking at high temperature because the thickness is too thin in design, it is able to bear the chemical material of high temperature , disposed through the special craft to adopt more than 30 kinds of expensive ones, not only tensile strength raise greatly, but also can abominable environment when being 30 degrees below zero - 80 degrees above zero use, overcome ordinary electric heat hand adopt PVC material easy wear out and critical defect of breaking etc..
Third, for prevent from , rotate handle line that throttle causes break the emergence of the situation, use the patented technology to adopt the special cable, include 84 shares of soft thin copper wires to form , cable rickshaw adopt the rubbery material to make into, even still keep the flexibility under the cold climatic conditions, can resist repeatedly and crookedly .
Fourth, in order to adjust the temperature, set up the regulator. Three ordinary shelf type regulators have level to block the temperature control, the middle shelf, in order to turn off two times. It is the high temperature upwards; it is the low temperature downwards.
Fifth, different season, different district different demands for temperature for convenience, de lure yeans of grades of temperature adjustment handle to employ patented technology can follow need, handle temperature can many shelf regulate, can regulate at will in 20 degrees- 65 degrees continuously, and each regulate the controller and adopt the leading technology of ” power of switch “, the regulator is power consumptive only watt 0.3, save the electricity further.
Sixth, for being easy to install, assemble, stay ingenious, save at motorcycle holing troubling to install regulator thermostat with left hand.
Seventh, install the difficulty in order to solve the left hand, it adopt by patented technology, left hand at design because it for device , roll especially with six maos there aren’t knife the screws to screw handle on, can be in order to take down the handle easily on the contrary. Be careful, can not be exerted one to twist screws very much. Eighth, ordinary electric heat hand adopt high, low two group generate heat the silk , high temperature or low-temperature, only one group generates heat, another group does not generate heat , cause some temperature of the handle to be overheated , it is apt to damage the handle.
Our company electric heat adopts unique form group silk wind, make evenly, and guarantee handle to be temperature even and soft hand
Comment by Mr Fuson — December 7, 2007 @